Page 1 of 1
ReelEx at ISE
Posted: Wed Jan 02, 2013 8:03 pm
by DanIsaac
Yes, I will be in the Shimano booth all week and will be taking reels with me for service.
You can $ave on shipping, and take advantage of $pecial Show Pricing at the same time.
Single reel $24, 3 reels for $66, or 6 reels for $126. This is excluding Calais and Stella which
run $28 each for the show.
Please at least stop by and say hey! I really enjoy putting names to faces!
Hope to see you all there!
Dan
Re: ReelEx at ISE
Posted: Thu Jan 03, 2013 10:41 pm
by kb
Sounds like a great deal see you at the show buddy!!!
kb
Re: ReelEx at ISE
Posted: Thu Jan 03, 2013 11:09 pm
by Vince Borges
Dan is the man! Hey Dan, what's the price to change out the bearings? Will you have a show special on the Orange Seal bearings as well? Thanks and see ya there!
Re: ReelEx at ISE
Posted: Fri Jan 04, 2013 5:11 pm
by DanIsaac
Thanks KB, and thanks Vince, the price on ABEC9 ceramic hybrid's is normally $25, but I am going to hold the price at $20 thru January even though the shipment that just arrived went UP again! Now's the time fellas....
I do have one additional incentive though.....for each reel brought to me at ISE the owner will receive one entry into a drawing for a supertuned, suped up Curado 200G5 complete with abec 9 ceramic hybrids. Drawing will be held at the completion of ISE and the prize reel will ship back included with the reels you have serviced.
Mention Western Bass or Ultimate Bass and receive and additional entry with your reels.
Should anyone have any questions please feel free to call anytime.
Thanks, Dan
650-454-4938
Re: ReelEx at ISE
Posted: Fri Jan 04, 2013 6:34 pm
by steve black
Dan, I have three old Batum Curados CU200bsf and CU200 are these too old to work on? They work fine but often wondered if a tune up would be a noticeable difference. I just can't seem to part with them when they work fine. Also do you prefer to have the spools stripped of line. Thanks
Re: ReelEx at ISE
Posted: Sat Jan 05, 2013 4:44 pm
by DanIsaac
Steve,
Absolutely, those reels will tune extremely well and they're our specialties. Line on or off is fine either way.
Thanks,
Dan
Re: ReelEx at ISE
Posted: Sun Jan 06, 2013 9:12 pm
by basslayer
I'll have a load of reels for you Dan. See you there.
Re: ReelEx at ISE
Posted: Mon Jan 07, 2013 5:25 pm
by DanIsaac
sounds good Adam...see ya there!
Re: ReelEx at ISE
Posted: Mon Jan 07, 2013 7:59 pm
by Zak Elrite
Dan, Awesome deal! I'm bringing some old bantam curados and a couple new"ish" ones, the D series I think. They need servicing baaad!
Re: ReelEx at ISE
Posted: Tue Jan 08, 2013 7:21 pm
by DanIsaac
look forward to it...got ya covered!
Re: ReelEx at ISE
Posted: Fri Jan 11, 2013 8:46 pm
by DanIsaac
still some room available...I hope everyone who has stopped by has enjoyed the show. Looking forward to Sat and Sunday!
Dan
Re: ReelEx at ISE
Posted: Sat Jan 12, 2013 9:38 pm
by DanIsaac
A special shout out to all who have stopped by, and to all of those who continue to support us, even in the midst of this tough economy. I can't thank you all enough, and I will continue to make every effort to provide the very best in service. I have too.
I have the best customers in this sport!
Thank you ALL again, very much!
Dan